Just How to Install a Bathtub Yourself: Removing and Replacing.
Just How to Install a Bathtub Yourself: Removing and Replacing.
Blog Article
We have stumbled upon the article about How to Install a Bathtub listed below on the net and think it made good sense to share it with you here.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult task. If the old tub is readily obtainable, the project can relocate immediately; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the new one. See to it you have qualified on your own for the job and also fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your tools as well as material checklist need to make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Secure the tap in place with the maker offered backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The former kind should be linked to the tap finishes first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, place the tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water as well as check all joints and also brand-new pipework for leaks and also tighten them if necessary. Load the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bathtub should wait until the tub has been made use of at least once as this will certainly resolve it into its last position.
Preparing for the Installment
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its final setting.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to enable the movement experienced when the tub is in use. The sealer can crack fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on How to Install a Bathtub Yourself, I assumed sharing that piece of content was smart. Appreciated our write-up? Please share it. Let others find it. I am grateful for your time. Visit again soon.
Click For More Info Report this page